DustFX MidiMax:CNC Industrial Dust Collection System

$ 12,499.95 CDN
$ 9,999.95 USD
+ $149 flat rate shipping on most items/ locations.
Confirm Availability
Thank you for your interest in CWI Woodworking Technologies! Prices quoted do not include shipping & handling fees and taxes. Fill the form below to receive the complete cost detail and inventory availability. All costs will be discussed and approved by the customer prior to any transaction of funds.

Flat rate shipping conditions: Most machines under 1000lbs delivered to most major North American cities or close to trucking warehouses might be eligible for $149.00 flat rate shipping. Rural areas and difficult trucking routes may incur additional charges.
Please enable JavaScript in your browser to complete this form.
Please include your full shipping address including your postal/zip code.
DustFX has designed the MidiMax:CNC for use with “dust difficult” machines like production CNC Routers and Edgebanders. DustFX has discovered that machines like these have different needs for proper collection of dust than other typical woodworking machines. Because of the operational design of woodworking machines like CNC Routers and Edgebanders, “pressure” is more important to remove dust particles than actual CFM. (Cubic feet per minute of air volume)
Product Details
Dust collectors are generally measured by CFM of air flow and “static pressure” (water lift). Typical dust collectors have difficulties with CNC because the cavity where dust is being made is really very wide open, not contained like a table saw or thickness planer.

Even though a dust collector may have a high volume of air movement (CFM) the “pulling pressure” may not be strong enough to collect the dust from a large opening like found on CNCs.

On an edgebander, the dust collection inlets are typically smaller diameter which “cuts off” the normal flow of CFM. By dramatically increasing the pressure of the air flow (which does not necessarily mean an increase in CFM) the MidiMax:CNC is able to properly pull the dust into the piping and back to the collection bins.
The MidiMax:CNC is manufactured in Italy with a specially designed impeller, housing, filter media and electrical system to provide an efficient, quiet and easy-to-use machine. The impeller design with a 5.5 hp 3-phase motor creates a very high amount of pressure to give extra “pulling power” for dust generated by the CNC cutting tools while operating at a low noise level of 78db.
There are 24 stainless-steel reinforced polyester dust sleeves providing 247 square feet of filtering surface area, allowing very efficient movement of air.
There is also a built-in electric shaker to clean the bags which activates each time the main power to the collector is turned off.

The collector has special electrics to allow being wired in directly with your CNC to turn on and off with the CNC power.
There are also available two optional 50-gallon steel “collector bins” on wheels with easy-to-dump handles and a window to know when dumping is needed.
The MidiMax:CNC Dust Collection System is truly unique in its design to provide superior performance with any CNC or Edgebander application.

– Spin Balanced Impeller Shielded from Dust
– Metal Quick Release Portable Dust Drum
– Dust Capacity of 18 Gallons
– Hepa Manual Clean Canister Filter
– Filters 99.97% of .3 micron and 100% of .5 Micron and larger
– Reusable Plastic Lower Collection Bag on Canister
– Heavy Structural Steel Frame
– Multi-Directional Casters for Ease of Movement
– 1250 CFM
– Sound Level @10’ is 74db
– 9” Water Lift
– Dual 4” Dust Inlets or one 6” diameter Inlet
– TEFC Industrial Duty Cycle 1.5 HP Motor
– 14 Amp 110/1/60
– CSA Electrics with Removable Safety Switch
– Floor Space 1000mm x 500mm x 1600mm
– Shipping Dimensions 1060mm x 570mm x 770mm
– 140 Pounds Shipping Weight
Confirm Availability & Shipping for the DustFX CWI-D1800M
Please enable JavaScript in your browser to complete this form.
Please include your full shipping address including your postal/zip code.